100% Free JNCIS-SP JN0-362 Dumps PDF Demo Cert Guide Cover
PDF Exam Material 2022 Realistic JN0-362 Dumps Questions
2. Junos Service Provider Switching (JSPX)
Junos Service Provider Switching (JSPX) also runs for 2 days. However, it focuses on switching skills and the relevant concepts such as provider bridging, Ethernet Operation, Administration, and Maintenance, spanning-tree protocols, VLAN translation, virtual LANs (VLANs), and bridging. Success in this course requires familiarity with the Junos OS Release 18.1R1.9, Open Systems Interconnection (OSI), and TCP/IP. It's important to note that this class is well-suited to all IT specialists who take pride in configuring or monitoring functional devices that run on the Junos OS. Also, exam-takers must be familiar with a set of Juniper products and solutions before enrolling in this training. This includes automation, switching, EX Series, Junos OS, and MX Series. When it comes to the content of such lessons, on the first day of your certification exam prep, you will be required to master the concepts of Ethernet Switching and Virtual LANs, Virtual Switches, and Provider Bridging. Of course, this is only possible after getting a sneak peek of the course through the introduction. That being said, the instructors will cover the following topics on the second day of this course:
- Spanning-Tree Protocols;
- Ethernet OAM;
- Troubleshooting and Monitoring.
- High Availability and Network Optimization;
NEW QUESTION 36
Click the Exhibit button. Which two topologies shown in the exhibit could be implemented without a spanning-tree protocol? (Choose two.)
- A. star
- B. ring
- C. mesh
- D. tree
Answer: A,D
NEW QUESTION 37
Click the Exhibit button.
Your co-worker configures the ge-0/0/0 interface with an IPv6 address of 2001:db8:0:9::/64. After committing the configuration, your co-worker executes the command shown in the exhibit.
What is the fe80::206:aff:fe0e:e01/64 address in this scenario?
- A. the link-local address
- B. the statically assigned address
- C. the loopback address
- D. the multicast address
Answer: A
NEW QUESTION 38
Which two values are used by an RSTP bridge to remove stale BPDU information? (Choose two.)
- A. Max Age
- B. Hello Time
- C. Message Age
- D. Forwarding Delay
Answer: A,C
NEW QUESTION 39
Click the Exhibit button.
Referring to the exhibit, which two statements are true? (Choose two.)
- A. The multi-hop statement is required for the BGP session to establish correctly
- B. The configuration is for an external BGP session
- C. The configuration is for an internal BGP session
- D. The local-address statement is required for the BGP session to establish correctly
Answer: C,D
NEW QUESTION 40
Click the exhibit.
You have configured OSPF between two routers. The OSPF adjacency will not form.
Referring to the exhibit, what is the problem?
- A. Router is not receiving hellos on the configured interface.
- B. The area does not match on the configured interfaces.
- C. The router is not sending hellos on the configured interface.
- D. The OSPF version does not match on the configured interfaces.
Answer: B
NEW QUESTION 41
Click the Exhibit button. The policy shown in the exhibit has been configured and installed on your router.
What is the result of applying this policy?
- A. The 172.18.1.0/24 network will be redistributed into OSPF as an external route.
- B. The 172.18.1.0/32 network will be redistributed into OSPF as an internal route.
- C. The 172.18.1.0/32 network will be redistributed into OSPF as an external route.
- D. The 172.18.1.0/24 network will be redistributed into OSPF as an internal route.
Answer: A
NEW QUESTION 42
You have a stub OSPF area running in your network. Your supervisor has asked you to build a virtual link across this area to connect new equipment acquired in a recent ISP acquisition.Which statement is correct about this scenario?
- A. Type 5 LSAs would be seen only in the newly attached area.
- B. Type 5 LSAs would carry external information across your transit area to the backbone.
- C. Type 5 LSAs would be converted to type 7 LSAs.
- D. Type 5 LSAs would be blocked in a stub area.
Answer: D
NEW QUESTION 43
By default, the Junos OS advertises which address(es) in LDP forwarding equivalency class (FEC) messages?
- A. loopback address
- B. all transit interfaces
- C. primary transit interface address
- D. all router addresses
Answer: A
NEW QUESTION 44
What is the purpose of STP BPDUs?
- A. to determine the least cost path
- B. to determine the root bridge
- C. to exchange MAC addresses
- D. to determine the root-alternate port
Answer: A
NEW QUESTION 45
Click the Exhibit button.
Your co-worker configures the ge-0/0/0 interface with an IPv6 address of 2001:db8:0:9::/64. After committing the configuration, your co-worker executes the command shown in the exhibit.
What is the fe80::206:aff:fe0e:e01/64 address in this scenario?
- A. the link-local address
- B. the statically assigned address
- C. the loopback address
- D. the multicast address
Answer: A
NEW QUESTION 46
Click the Exhibit button.
You have configured IPv6 over IPv4 tunneling, as shown in the exhibit. However, hosts connected to network 2001:0:0:1::0/64 cannot communicate with hosts on network 2001:0:0:2::0/64. The router R2 has a similar configuration as the R1 router.
How would you solve this problem?
- A. Configure the next hop of the inet6.0 static route to point to the physical interface between the routers
- B. Configure the next hop of the inet6.0 static route to point to the IPv4 address of the remote router
- C. Configure an IPv6 address on the tunnel interfaces
- D. Configure an IGP across the tunnel interfaces
Answer: B
NEW QUESTION 47
Because of recent network failures, additional circuits have been purchased. In addition, Fast reroute has been configured on critical MPLS LSPs.
When the next failure occurs, which two time intervals will affect fast reroute? (Choose two.)
- A. The amount of time it takes to ping the gateway on the detour link
- B. The amount of time required to recalculate the best detour
- C. The amount of time required to reroute the traffic onto the detour
- D. The amount of time to detect a link or node failure
Answer: C,D
NEW QUESTION 48
You are setting up a new IS-IS adjacency between two devices. The new Level1 adjacency is not establishing.
What would cause this behavior?
- A. The Level 1 routers have mismatched area IDs.
- B. The router ID has not been explicitly configured.
- C. The routers support a minimum MTU of 1492 bytes.
- D. The IP addresses are on different subnets.
Answer: A
NEW QUESTION 49
The IPv6 Neighbor Discovery Protocol (NDP) performs the same function as which two IPv4 protocols? (Choose two.)
- A. ICMP
- B. DNS
- C. DHCP
- D. ARP
Answer: A,D
NEW QUESTION 50
Click the Exhibit button.
Referring to the exhibit, which statement is true?
- A. The router will prune links with insufficient bandwidth from the path before beginning the signaling process
- B. The router will precalculate a valid path through the network for LSP r1-to-r3
- C. The router will analyze the traffic engineering database to determine the best path through the network
- D. The router will attempt to signal the LSP along the IGP shortest path to 192.168.100.1
Answer: A
NEW QUESTION 51
Click the Exhibit button. Referring to the exhibit, what must be true of the vlan_100 bridge domain?
- A. vlan_100 has at least one Ethernet interface assigned to it.
- B. vlan_100 does not have an active Ethernet interface assigned to it.
- C. vlan_100 does not have an Ethernet interface assigned to it.
- D. vlan_100 might have an active Ethernet interface assigned to it.
Answer: B
NEW QUESTION 52
Which type of router can provide connectivity between areas in an IS-IS domain?
- A. a Level 2 router with adjacencies in more than one area
- B. a Level 1 router with adjacencies within a single area
- C. an area border router with adjacencies in more than one area
- D. a Level 2 router with adjacencies in a single area
Answer: A
NEW QUESTION 53
What are three label operations that an MPLS-enabled router performs? (Choose three.)
- A. push
- B. pop
- C. rewrite
- D. swap
- E. insert
Answer: A,B,D
NEW QUESTION 54
What is the size of the unique address used to identify each node on an Ethernet LAN?
- A. 9 bytes
- B. 6 bytes
- C. 12 bytes
- D. 3 bytes
Answer: B
NEW QUESTION 55
Click the Exhibit button. Based on the configuration shown in the exhibit, what will be the state of the IS-IS levels on interface ge-0/0/0.100?
- A. Level 1 is disabled and Level 2 is enabled.
- B. Level 1 is enabled and Level 2 is enabled.
- C. Level 1 is disabled and Level 2 is disabled.
- D. Level 1 is enabled and Level 2 is disabled.
Answer: C
NEW QUESTION 56
......
Updated Juniper JN0-362 Dumps – PDF & Online Engine: https://www.easy4engine.com/JN0-362-test-engine.html
