500-920 Practice Exam and Study Guides - Verified By Easy4Engine Updated 42 Questions
2021 Updated Verified Pass 500-920 Study Guides & Best Courses
Cisco 500-920 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
NEW QUESTION 13
When booting up a Cisco UCS Server you want to see boot time diagnostic messages of the POST, what action is required for you to do so?
- A. Restart the Server
- B. Disable Fast Boot on the Server's Service Profile
- C. Enable Quiet Boot on the Server's Service Profile
- D. Enable Quiet Boot on the Server's BIOS
- E. Disable Fast Boot on the Server's BIOS
Answer: C
NEW QUESTION 14
What is the likely cause of an intermittent SAN Boot fails?
- A. Wrong boot order in the service profile
- B. Misconfigured SAN boot target in the boot policy of the service profile
- C. FCoE used instead of FC
- D. LUN ID Mismatch
Answer: B
NEW QUESTION 15
What is the next step after performing a UCS firmware upgrade, and downloading the latest drivers both for your RAID Controller and your Fibre Channel HBA?
Check the HCL
- A. Test device driver compatibility
- B. No need to do anything Drivers are automatically installed for you
- C. Apply the device driver update to the devices
- D. No Drivers are needed in a UCS environment
Answer: A
NEW QUESTION 16
Which statement is true when using SPAN for Fibre Channel (FC) Traffic?
- A. When defining FC uplink port as the SPAN destination, system will automatically stop using that port as an uplink port
- B. For FC SPAN sessions we do not have to specifically enable the monitoring session
- C. FC port on Cisco UCS 6238UP can be used as a SPAN source
- D. Any port can be used as a SPAN destination port Even if it is defined as Eth uplink port it will be automatically converted to FC uplink port
Answer: C
NEW QUESTION 17
What is the result of enabling the Core File Exporter in UCS Manager?
- A. A core dump file will be immediately created and transmitted using HTTP protocol
- B. A core dump must be remotely activated by Cisco TAC.
- C. A core dump will immediately be generated and will be exported
- D. If a subsequent triggering event occurs, a core dump will be generated and sent by TFTP
Answer: C
NEW QUESTION 18
When troubleshooting UCS initialization issues that require Fabric Interconnect reboots, which Fabric Interconnect should be rebooted first?
- A. The Cisco UCS Manager will determine with Fabric Interconnect to reboot
- B. The subordinate Fabric Interconnect
- C. Both Fabric Interconnects must be rebooted simultaneously
- D. The primary Fabric Interconnect
Answer: D
NEW QUESTION 19
An overvoltage condition has occurred on a UCS server However the Cisco IMC System Event Log (SEL) file is full What is the resulting fault logging action?
- A. The overvoltage condition event will not be recorded in the SEL.
- B. The oldest entry in the SEL will be overwritten by the overvoltage condition event
- C. The newest entry in the SEL will be overwritten by the overvoltage condition event.
- D. The SEL is not used to record server related events, such as overvoltage conditions.
Answer: A
NEW QUESTION 20
A Hard Drive (HDD) has been hot swapped in a UCS server blade, however, the UCS Manager GUI is not displaying updated metrics about the replacement drive. What action will be required to properly display updated metrics?
- A. Use the CLI, since HDD metrics cannot be displayed with the UCS Manager GUI
- B. Remove and re-insert the server blade HDD controller mezzanine card
- C. Reboot the Fabric Interconnects
- D. Reboot the server.
Answer: B
NEW QUESTION 21
Which are two benefits of integrating Cisco UCS C-series servers with Cisco UCS Manager? (Choose two ) Cisco UCS Manager provides the ability to automatically update C-series firmware and device drivers from a single global interface.
- A. Cisco UCS Manager can automatically power on and off servers to scale elastically according to application performance demands
- B. Cisco UCS Manager is able to act as a common centralized management platform for both blade and rack servers in a single domain.
- C. Cisco UCS Manager uses service profiles and resource pools to allow the deployment of multiple servers with a single common template
- D. Cisco UCS Manager provides the ability to manage C-series in multiple physical domains from a single global interface
Answer: B
NEW QUESTION 22
The UCS Chassis Discovery Policy has been set to four and a new chassis is connected with two links What is the resulting chassis recognition action?
- A. The Chassis Discovery Policy will automatically reset to two links, since it always tracks the physical connections
- B. The chassis will not be recognized
- C. The chassis will be recognized and both links will be active
- D. The chassis will be recognized but only one of the links will be active.
Answer: B
NEW QUESTION 23
Which statement regarding the UCS C-senes connectivity modes best describes connectivity options in a UCS Manager integrated environment?
- A. UCS C-series servers may be connected to multiple UCS Manager domains at the same time
- B. UCS C-series servers must be connected to Fabric Interconnects using Fabric Extenders (FEX)
- C. UCS C-series servers may be connected with or without the use of Fabric Extenders (FEX) in environments running UCS Manager Software Release 2 2 or later
- D. All UCS C-series servers in a single UCS Manager domain must share the same connectivity model
Answer: C
NEW QUESTION 24
What are three possible causes of service profile association failure due to iSCSI configuration issue? (Choose three )
- A. iSCSI Target out of configured range of services
- B. Inappropriate network configuration
- C. Misconfigured LUN. LUN masking
- D. Misconfigured iSCSI parameters
- E. Improperly assigned iSCSI Class of Service
- F. Wrong WWNN
Answer: A,B,D
NEW QUESTION 25
Which Cisco UCS internal component maintains the UCS XML database, manages the FSM stages and operations and instructs the Application Gateway to perform operations on physical and logical elements?
- A. Cisco Finite State Machine
- B. Cisco Application Gateways
- C. Cisco Data Management Engine
- D. Cisco UCS Manager
Answer: C
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/GUI-User-Guides/System-Monitoring/3-1/b_UCSM_GUI_System_Monitoring_Guide_3_1/b_UCSM_GUI_System_Monitoring_Guide_3_1_chapter_0100.html
NEW QUESTION 26
After installing a new UCS M4 server, which two Cisco Integrated Management Controller connectivity options do you have? (Choose two )
- A. Out-of-Band Access
- B. XML API Access
- C. SNMP
- D. In-band Access
- E. Web Access
Answer: B,D
NEW QUESTION 27
In order to create an Inband Profile for Cisco Integrated Management Controller (IMC) connectivity, what do you need to perform first?
- A. Create a Management IP Pool, a MAC Address Pool, and a VLAN Pool
- B. Create an IPMI Policy
- C. Create different VLANs, with different VLAN IDs
- D. Create a Management IP Pool, a VLAN. and a VLAN Group
- E. Create a Service Profile
Answer: E
NEW QUESTION 28
What three options should be verified, when you are able to connect to Cisco UCS Manager, but unable to open a KVM session to a blade? (Choose three)
- A. Verify TCP port 2068 is not blocked by an ACL or Firewall
- B. Confirm the IP Address assigned to UCS Manager is the same as the KVM address
- C. Verify the KVM IP Address is on the same subnet as the Fabric Interconnect management address
- D. Confirm the IP Address assigned to the KVM is not a duplicate IP
- E. Confirm the KVM IP Address is added to the route table in Cisco UCS Manager
- F. Verify the KVM IP Address is on the same ip subnet as the virtual machines
Answer: A,D,E
NEW QUESTION 29
......
Ultimate Guide to the 500-920 - Latest Edition Available Now: https://www.easy4engine.com/500-920-test-engine.html
