Ultimate Guide to Prepare Free Fortinet NSE6_FWF-6.4 Exam Questions and Answer
Pass Fortinet NSE6_FWF-6.4 Tests Engine pdf - All Free Dumps
NEW QUESTION 10
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength weaker than -68 dB are cut out of the map
- B. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
- C. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
- D. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
Answer: B
NEW QUESTION 11
Refer to the exhibits.
Exhibit A
Exhibit B
A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network.
Which two configuration changes will resolve the issue? (Choose two.)
- A. Disable intra-vap-privacy for the Authors vap-wireless network
- B. For both interfaces in the wtp-profile, configure set vaps to be "Authors"
- C. For both interfaces in the wtp-profile, configure vap-all to be manual
- D. Increase the transmission power of the AP radio interfaces
Answer: A,C
NEW QUESTION 12
Which factor is the best indicator of wireless client connection quality?
- A. Upstream link rate, the connection rate for the client to the AP
- B. The receive signal strength (RSS) of the client at the AP
- C. The channel utilization of the channel the client is using
- D. Downstream link rate, the connection rate for the AP to the client
Answer: B
Explanation:
SSI, or "Received Signal Strength Indicator," is a measurement of how well your device can hear a signal from an access point or router. It's a value that is useful for determining if you have enough signal to get a good wireless connection.
NEW QUESTION 13
How are wireless clients assigned to a dynamic VLAN configured for hash mode?
- A. Using the current number of wireless clients connected to the SSID and the number of clients allocated to each of the VLANs
- B. Using the current number of wireless clients connected to the SSID and the number of IPs available in the least busy VLAN
- C. Using the current number of wireless clients connected to the SSID and the number of VLANs available in the pool
- D. Using the current number of wireless clients connected to the SSID and the group the FortiAP is a member of
Answer: C
Explanation:
VLAN from the VLAN pool based on a hash of the current number of SSID clients and the number of entries in the VLAN pool.
NEW QUESTION 14
When deploying a wireless network that is authenticated using EAP PEAP, which two configurations are required? (Choose two.)
- A. A WPA2 or WPA3 personal wireless network
- B. An X.509 to authenticate the authentication server
- C. A WPA2 or WPA3 Enterprise wireless network
- D. An X.509 certificate to authenticate the client
Answer: B,C
NEW QUESTION 15
Which two statements about background rogue scanning are correct? (Choose two.)
- A. Background rogue scanning requires DARRP to be enabled on the AP instance
- B. A dedicated radio configured for background scanning can detect rogue devices on all other channels in its configured frequency band
- C. A dedicated radio configured for background scanning can support the connection of wireless clients
- D. When detecting rogue APs, a dedicated radio configured for background scanning can suppress the rogue AP
Answer: C,D
Explanation:
To enable rogue AP scanning
NEW QUESTION 16
Part of the location service registration process is to link FortiAPs in FortiPresence.
Which two management services can configure the discovered AP registration information from the FortiPresence cloud? (Choose two.)
- A. FortiSwitch
- B. FortiGate
- C. AP Manager
- D. FortiAP Cloud
Answer: B,D
Explanation:
FortiGate, FortiCloud wireless access points (send visitor data in the form of station reports directly to FortiPresence)
NEW QUESTION 17
Which statement describes FortiPresence location map functionality?
- A. Provides real-time insight into user purchase activity
- B. Provides real-time insight into user usage stats
- C. Provides real-time insight into user online activity
- D. Provides real-time insight into user movements
Answer: D
NEW QUESTION 18
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit C
A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and IoT devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?
- A. Enable frequency handoff on the AP to band steer clients
- B. Install another AP in the reception area to improve available bandwidth
- C. Reduce the number of wireless networks being broadcast by the AP
- D. Increase the transmission power of the AP radios
Answer: D
NEW QUESTION 19
Refer to the exhibits.
Exhibit A
Exhibit B
The exhibits show the diagnose debug log of a station connection taken on the controller CLI.
Which security mode is used by the wireless connection?
- A. WPA2 Personal and radius MAC filtering
- B. Open, with radius MAC filtering
- C. WPA3 Enterprise
- D. WPA2 Enterprise
Answer: D
Explanation:
Best security option is WPA2-AES.
NEW QUESTION 20
When using FortiPresence as a captive portal, which two types of public authentication services can be used to access guest Wi-Fi? (Choose two.)
- A. Social networks authentication
- B. Hardware security token authentication
- C. Software security token authentication
- D. Short message service authentication
Answer: A,D
NEW QUESTION 21
Where in the controller interface can you find a wireless client's upstream and downstream link rates?
- A. On the AP CLI, using the cw_diag ksta command
- B. On the AP CLI, using the cw_diag -d sta command
- C. On the controller CLI, using the diag wireless-controller wlac -d sta command
- D. On the controller CLI, using the WiFi Client monitor
Answer: A
NEW QUESTION 22
Which factor is the best indicator of wireless client connection quality?
- A. The channel utilization of the channel the client is using
- B. The receive signal strength (RSS) of the client at the AP
- C. Upstream link rate, the connection rate for the client to the AP
- D. Downstream link rate, the connection rate for the AP to the client
Answer: C
NEW QUESTION 23
When enabling security fabric on the FortiGate interface to manage FortiAPs, which two types of communication channels are established between FortiGate and FortiAPs? (Choose two.)
- A. Data channels
- B. Security channels
- C. Control channels
- D. FortLink channels
Answer: A,C
Explanation:
The control channel for managing traffic, which is always encrypted by DTLS. l The data channel for carrying client data packets.
NEW QUESTION 24
When using FortiPresence as a captive portal, which two types of public authentication services can be used to access guest Wi-Fi? (Choose two.)
- A. Social networks authentication
- B. Short message service authentication
- C. Hardware security token authentication
- D. Software security token authentication
Answer: A,C
Explanation:
This information along with the social network authentication logins with Facebook, Google, Instagram, LinkedIn, or FortiPresence using your WiFi.
Captive Portal configurations for social media logins and internet access. You can add and manage sites using the integrated Google maps and manoeuvre your hardware infrastructure easily.
NEW QUESTION 25
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
- B. Areas with the signal strength weaker than -68 dB are cut out of the map
- C. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
- D. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
Answer: C
NEW QUESTION 26
As standard best practice, which configuration should be performed before configuring FortiAPs using a FortiGate wireless controller?
- A. Preauthorize APs
- B. Create a custom AP profile
- C. Create wireless LAN specific policies
- D. Set the wireless controller country setting
Answer: D
NEW QUESTION 27
Which two configurations are compatible for Wireless Single Sign-On (WSSO)? (Choose two.)
- A. A VAP configured to authenticate using a radius server
- B. A VAP configured for WPA2 or 3 Enterprise
- C. A VAP configured for captive portal authentication
- D. A VAP configured to authenticate locally on FortiGate
Answer: A,B
Explanation:
In the SSID choose WPA2-Enterprise authentication.
WSSO is RADIUS-based authentication that passes the user's user group memberships to the FortiGate.
NEW QUESTION 28
What is the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration?
- A. Multicast
- B. Static
- C. DHCP
- D. Broadcast
Answer: C
NEW QUESTION 29
......
Fortinet NSE 6 - Secure Wireless LAN 6.4 Practice Tests 2023 | Pass NSE6_FWF-6.4 with confidence!: https://drive.google.com/open?id=1wiOPNBsb2XD86DdCOjSjaohGq2TVBRKX
Online Exam Practice Tests with detailed explanations!: https://www.easy4engine.com/NSE6_FWF-6.4-test-engine.html
