Valid NS0-014 Exam Dumps Ensure you a HIGH SCORE (2025)
Pass NS0-014 Exam with Latest Questions
NEW QUESTION # 49
When troubleshooting a failed switch in a MetroCluster environment, which command helps you identify if the switch is still part of the cluster network?
- A. metrocluster interconnect show
- B. cluster show
- C. metrocluster check network
- D. switch status
Answer: A
NEW QUESTION # 50
What is the purpose of the MetroCluster Tiebreaker software in a MetroCluster configuration?
- A. To replicate data asynchronously between sites
- B. To optimize network performance
- C. To manage ATTO FibreBridges
- D. To monitor the health of the clusters and manage failover
Answer: D
NEW QUESTION # 51
What are two critical elements of the physical layer in an FC MetroCluster configuration? (Select two)
- A. Ethernet switches
- B. ATTO FibreBridge
- C. FC switches
- D. Mediator server
Answer: B,C
NEW QUESTION # 52
What is a key benefit of transitioning from FC MetroCluster to IP MetroCluster?
- A. Faster data replication
- B. Improved storage capacity
- C. Reduced hardware costs and longer distance support
- D. Less frequent software updates
Answer: C
NEW QUESTION # 53
When validating the health of a MetroCluster IP configuration, which two tools are essential for network validation? (Select two)
- A. NetApp Interoperability Matrix Tool (IMT)
- B. Network troubleshooting tools (ping, traceroute)
- C. OnCommand Unified Manager
- D. Config Advisor
Answer: B,D
NEW QUESTION # 54
Which two configuration steps are essential when installing MetroCluster Tiebreaker software?
(Select two)
- A. Set up IP connectivity between clusters
- B. Configure cross-site LIFs
- C. Enable SyncMirror
- D. Install ONTAP Mediator
Answer: A,B
NEW QUESTION # 55
Which ONTAP service replicates cluster configuration between MetroCluster sites?
- A. vldb
- B. vifmgr
- C. mgmt
- D. crs
Answer: B
NEW QUESTION # 56
Which MetroCluster component requires reconfiguration when upgrading from a 2-node to a 4- node configuration?
- A. Mediator
- B. FC switches
- C. SyncMirror
- D. ATTO FibreBridge
Answer: B
NEW QUESTION # 57
During the planning phase, which component is used to manage and monitor the MetroCluster environment?
- A. System CLI
- B. Active IQ Unified Manager
- C. Cloud Manager
- D. MetroCluster Manager
Answer: B
NEW QUESTION # 58
Which two tasks are critical during the initial setup of a MetroCluster solution? (Select two)
- A. Setting up Snapshot policies
- B. Ensuring proper physical cabling and connectivity
- C. Configuring the network bandwidth
- D. Synchronizing data between sites
Answer: B,D
NEW QUESTION # 59
What are two methods to verify that MetroCluster replication is functioning properly? (Choose two)
- A. Check IP route tables between sites
- B. Verify data consistency using SnapMirror
- C. Perform a data validation using Config Advisor
- D. Use the metrocluster check command
Answer: B,D
NEW QUESTION # 60
A customer has a MetroCluster in which one site had suffered a power outage. The MetroCluster performed a switchover to the secondary site. The storage administrator is now preparing to run a DR switchback, to restore normal operations across the two sites for the MetroCluster.
Which two commands does the administrator have to run before the switchback? (Choose two).
- A. storage aggregate mirror
- B. metrocluster heal root-aggregates
- C. metrocluster heal aggregates
- D. snapmirror resync
Answer: B,C
NEW QUESTION # 61
Which tool is used to perform a disaster recovery simulation in an IP MetroCluster environment?
- A. ONTAP Mediator
- B. OnCommand System Manager
- C. MetroCluster Switchover Simulator
- D. MetroCluster Tiebreaker
Answer: D
NEW QUESTION # 62
What are two core components of a MetroCluster IP architecture? (Select two)
- A. Inter-Switch Links (ISLs)
- B. Fibre Channel switches
- C. SyncMirror
- D. ATTO FibreBridge
Answer: A,C
NEW QUESTION # 63
What is a critical requirement for transitioning a MetroCluster environment from 7-Mode to Clustered ONTAP?
- A. Manually updating all ONTAP licenses
- B. Replacing all storage hardware
- C. Using the 7-Mode Transition Tool
- D. Reconfiguring IP switches
Answer: C
NEW QUESTION # 64
What role does SyncMirror play in a MetroCluster configuration?
- A. Asynchronous data replication
- B. Synchronous data mirroring between two sites
- C. Load balancing
- D. Data backup
Answer: B
NEW QUESTION # 65
Which switch configuration is necessary for the communication between MetroCluster nodes?
- A. Ethernet switches in loop mode
- B. FC switches with ISL links
- C. Fibre Channel over Ethernet (FCoE) switches
- D. IP-based switches with cross-links
Answer: B
NEW QUESTION # 66
What is the primary benefit of upgrading the Mediator in a MetroCluster configuration?
- A. Higher storage capacity
- B. Improved failover response time and reliability
- C. Faster replication speed
- D. Simplified configuration management
Answer: B
NEW QUESTION # 67
In a MetroCluster environment, which two steps are required to configure FC switches? (Select two)
- A. Configure IPsec for secure communication
- B. Configure VSANs for all switches
- C. Set up inter-switch links (ISLs) between the FC switches
- D. Enable NPIV (N-Port ID Virtualization)
Answer: C,D
NEW QUESTION # 68
What are two requirements when transitioning from FC MetroCluster to IP MetroCluster? (Select two)
- A. Remove ATTO FibreBridges
- B. Replace FC switches with IP switches
- C. Upgrade to a compatible ONTAP version
- D. Maintain existing FC paths
Answer: B,C
NEW QUESTION # 69
Which task must be completed first when upgrading MetroCluster hardware components?
- A. Install the Mediator software
- B. Install new ATTO FibreBridges
- C. Update the ONTAP software
- D. Validate system compatibility using IMT
Answer: D
NEW QUESTION # 70
Which component is responsible for managing site failover in an IP-based MetroCluster?
- A. SnapMirror
- B. ONTAP Mediator
- C. SyncMirror
- D. ATTO FibreBridge
Answer: B
NEW QUESTION # 71
When the administrator of a MetroCluster configuration creates a mirrored aggregate on the local cluster, which action automatically occurs on both clusters?
- A. A DR group is created.
- B. A failover group is created.
- C. A plex is created.
- D. An SVM DR is created.
Answer: C
NEW QUESTION # 72
Which two components must be validated to ensure the proper functioning of a Fibre Channel MetroCluster configuration? (Choose two)
- A. Fibre Channel zoning
- B. Mediator configuration
- C. SnapMirror configuration
- D. ATTO Bridge health
Answer: A,D
NEW QUESTION # 73
......
NS0-014 Exam Practice Questions prepared by Network Appliance Professionals: https://www.easy4engine.com/NS0-014-test-engine.html
Use Valid New NS0-014 Questions - Top choice Help You Gain Success: https://drive.google.com/open?id=1lZopKuudZuoAcruR6IpPo6X8Ds5a4qMq
